Abit AMD ATHLON KV8 PRO Bedienungsanleitung

KV8 Pro AMD AthlonTM 64 System Board Socket 754 User’s Manual 4200-0405-01 Rev. 1.00

2-2 Chapter 2 2-2. Install CPU and Heatsink This motherboard provides a ZIF (Zero Insertion Force) Socket 754 to install AMD Socket 754 CPU. The CPU

Hardware Setup 2-3 2-3. Install System Memory This motherboard provides 2 184-pin DDR DIMM slots for memory expansion available from minimum 128MB t

2-4 Chapter 2 Power off the computer and unplug the AC power cord before installing or removing memory modules. 1. Locate the DIMM slot on the board

Hardware Setup 2-5 2-4. Connectors, Headers and Switches Here we will show you all of the connectors, headers and switches, and how to connect them.

2-6 Chapter 2 (2). FAN Connectors These 3-pin connectors each provide power to the cooling fans installed in your system. The CPU must be kept cool b

Hardware Setup 2-7 (3). CMOS Memory Clearing Header This header uses a jumper cap to clear the CMOS memory. • Pin 1-2 shorted (default): Normal ope

2-8 Chapter 2 (4). Wake-up Header These headers use a jumper cap to enable/disable the wake-up function. • USBPWR1: Pin 1-2 shorted (default): Disab

Hardware Setup 2-9 (5). Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the chassis

2-10 Chapter 2 (6). Additional USB Port Headers These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for U

Hardware Setup 2-11 (7). Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. • To use the au

Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of th

2-12 Chapter 2 (8). Internal Audio Connectors These connectors connect to the audio output of internal CD-ROM drive or add-on card. KV8 Pro

Hardware Setup 2-13 (9). Accelerated Graphics Port Slot This slot supports an optional AGP graphics card up to AGP 8X mode. Please refer to our Web

2-14 Chapter 2 (10). Floppy Disk Drive Connector This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable. Conn

Hardware Setup 2-15 (11). IDE Connectors This motherboard provides two IDE ports to connect up to four IDE drives at Ultra DMA mode by Ultra AT

2-16 Chapter 2 (12). POST Code Display This is an LED device to display the “POST” Code, the acronym of Power On Self Test. The computer will execute

Hardware Setup 2-17 (13). Serial ATA Connectors These connectors are provided to attach one Serial ATA device at each channel via Serial ATA cable.

2-18 Chapter 2 (14). Status Indicators • LED1 (5VSB): This LED lights up when the power supply is connected with power source. • LED2 (VCC): This L

Hardware Setup 2-19 (15). System Management Bus Headers This header is reserved for system management bus (SM bus). The SM bus is a specific impleme

2-20 Chapter 2 (16). Back Panel Connectors • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. • LPT1: Connects to printer or

BIOS Setup 3-1 Chapter 3. BIOS Setup This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS (Basic Input/Out

Table Of Contents Chapter 1. Introduction ... 1-1 1-1. Features & Specif

3-2 Chapter 3 F6: You may create a profile to save the new BIOS settings in it. Press <F6> button in the main menu, a dialog box with five numb

BIOS Setup 3-3 3-1. µGuru Utility Brand Name: This item displays the CPU model name, for example: AMD AthlonTM 64 processor 3200+. Frequency: This i

3-4 Chapter 3 Voltages Control: This option allows you to switch between the default and user-defined voltages. Leave this setting to default unless

BIOS Setup 3-5  Back to µGuru Utility Setup Menu: Use <→> key to switch from OC Guru setup menu to ABIT EQ setup menu: ABIT EQ Beep Control:

3-6 Chapter 3  Shutdown Temp.: This items sets the temperature that would shutdown the system automatically in order to prevent system overheats. 

BIOS Setup 3-7  Fan Speed Monitoring: Click <Enter> key to enter its submenu: CPU/NB/SYS/AUX1/AUX2 FAN Speed: These items display the speed o

3-8 Chapter 3  FanEQ Control: Click <Enter> key to enter its submenu: CPU/NB/SYS FanEQ Control: When set to [Enabled], these items allow you

BIOS Setup 3-9 3-2. Standard CMOS Features This section contains the basic configuration parameters of the BIOS. These parameters include date, hour

3-10 Chapter 3 IDE Channel 1 Master / Slave, IDE Channel 2 Master / Slave: When set to [Auto], the BIOS will automatically check what kind of IDE dri

BIOS Setup 3-11 [EGA/VGA]: (Enhanced Graphics Adapter/Video Graphics Array) For EGA, VGA, SVGA and PGA monitor adapters. [CGA 40]: (Color Graphics Ad

3-10. Set Password ...3-26 3-11. Save & Exit Setup ...

3-12 Chapter 3 3-3. Advanced BIOS Features Hard Disk Boot Priority: This item selects the hard disks booting priority. By pressing <Enter> ke

BIOS Setup 3-13 [Setup]: The password is required only when accessing the BIOS Setup. [System]: The password is required each time the computer boots

3-14 Chapter 3 3-4. Advanced Chipset Features AGP & P2P Bridge Control: Click <Enter> key to enter its submenu: AGP Aperture Size: This

BIOS Setup 3-15 AGP Fast Write: Two options are available: Disabled  Enabled. The default setting is Enabled. If your AGP adapter can support this f

3-16 Chapter 3 DRAM Timing Selectable: Two options are available: Manual  By SPD. The default setting is By SPD. When set to “By SPD”, the BIOS will

BIOS Setup 3-17  Back to Advanced Chipset Features Setup Menu: LDT & PCI Bus Control: Click <Enter> key to enter its submenu: Upstream/Do

3-18 Chapter 3 3-5. Integrated Peripherals OnChip IDE Device: Click <Enter> key to enter its submenu: SATA RAID ROM: This item allows you to

BIOS Setup 3-19  Back to Integrated Peripherals Setup Menu: OnChip PCI Device: Click <Enter> key to enter its submenu: OnChip Audio Controlle

3-20 Chapter 3  Back to Integrated Peripherals Setup Menu: SuperIO Device: Click <Enter> key to enter its submenu: Onboard FDD Controller: Tw

BIOS Setup 3-21 3-6. Power Management Setup ACPI Suspend Type: This item selects the type of Suspend mode. [S1(PowerOn-Suspend)]: Enables the Power

Introduction 1-1 Chapter 1. Introduction 1-1. Features & Specifications 1. CPU • Supports 64-bit AMD AthlonTM 64 processor (Socket 754) • 160

3-22 Chapter 3 [Power Off]: When power returns after an AC power failure, the system’s power remains off. You must press the Power button to power-on

BIOS Setup 3-23 NOTE: To enable this “Power On” function, the wake-up header of [USBPWR1] and [USBPWR2] must be set to [Enabled] position. Please ref

3-24 Chapter 3 3-7. PnP/PCI Configurations Resources Controlled By: This item configures all of the boot and Plug-and-Play compatible devices. [Auto

BIOS Setup 3-25 PIRQ_0 Use IRQ No. ~ PIRQ_7 Use IRQ No.: This item specifies the IRQ number manually or automatically for the devices installed on PC

3-26 Chapter 3 3-8. Load Fail-Safe Defaults This option loads the BIOS default values for the most stable, minimal-performance system operations. 3-

Install VIA 4-in-1 Driver A-1 Appendix A. Install VIA 4-in-1 Driver NOTE: Please install this VIA 4-in-1 driver first after having installed the Win

A-2 Appendix A Click [Next]. 6. 7. Choose [Yes, I want to restart my computer now.], and click [OK] to complete setup. KV8 Pro

Install Audio Driver B-1 Appendix B. Install Audio Driver The installation procedures and screen shots in this section are based on Windows XP oper

B-2 Appendix B B-2 Appendix B KV8 Pro KV8 Pro

Install LAN Driver C-1 Appendix C. Install LAN Driver To install the LAN driver, please insert the Driver & Utility CD into CD-ROM drive. It sho

1-2 Chapter 1 • 2x USB headers • 1x CD-IN, 1x AUX-IN header 9. Back Panel I/O • 1x PS/2 keyboard, 1x PS/2 mouse • 1x Serial port connector, 1x P

C-2 Appendix C KV8 Pro

Install VIA USB 2.0 Driver D-1 Appendix D. Install VIA USB 2.0 Driver NOTE: There is no need to install VIA USB 2.0 driver for the Windows XP operat

D-2 Appendix D Click [Yes]. 6. Click [OK]. 7. Click [Print to File]. 8. Click [OK]. 9. KV8 Pro

Install VIA Serial ATA RAID Driver E-1 Appendix E. Install VIA Serial ATA RAID Driver The installation procedures and screen shots in this section

E-2 Appendix E 6. Choose [Yes, I want to restart my computer now.], and click [Finish] to complete setup. 7. After the system restarted, a shortc

Install ABIT µGuru Driver F-1 Appendix F. Install ABIT µGuru Driver ABIT µGuru is a fresh Microprocessor developed by ABIT engineers used only on AB

F-2 Appendix F KV8 Pro

POST Code Definition G-1 Appendix G. POST Code Definition AWARD POST Code Definition: POST (hex) Description CF Test CMOS R/W functionality C0 Early

G-2 Appendix G 1F Load keyboard matrix (notebook platform) 21 HPM initialization (notebook platform) 23 1. Check validity of RTC value: e.g. a value

POST Code Definition G-3 55 Display number of processors (multi-processor platform) 57 Display PnP logo Early ISA PnP initialization -Assign CSN to e

Introduction 1-3 1-2. Layout Diagram User’s Manual

G-4 Appendix G 8B 1. Invoke all ISA adapter ROMs 2. Invoke all PCI ROMs (except VGA) 8D 1. Enable/Disable Parity Check according to CMOS setup 2. APM

POST Code Definition G-5 AC2003 POST Code Definition: POST (hex) Description Power On Sequence 8.1. Start power on sequence 8.2. Enable ATX power sup

G-6 Appendix G KV8 Pro

Troubleshooting (Need Assistance?) H-1 Appendix H. Troubleshooting (Need Assistance?) Q & A: Q: Do I need to clear the CMOS before I use a new

H-2 Appendix H Q: How can I get a quick response to my request for technical support? A: Be sure to follow the guidelines as stated in the “Technic

Troubleshooting (Need Assistance?) H-3 Main instructions: To fill in this “Technical Support Form”, refer to the step-by-step instructions given belo

H-4 Appendix H  Technical Support Form  Company Name:  Phone Number:  Contact Person:  Fax Number:  E-mail Address: Model * BIOS ID #

How to Get Technical Support I-1 Appendix I. How to Get Technical Support (From our website) http://www.abit.com.tw (In North America) http://www.ab

I-2 Appendix I 4. Internet Newsgroups. They are a great source of information and many people there can offer help. ABIT's Internet News group,

How to Get Technical Support I-3 North America and South America: ABIT Computer (U.S.A.) Corporation 45531 Northport Loop West, Fremont, California

1-4 Chapter 1 KV8 Pro

I-4 Appendix I 7. RMA Service. If your system has been working but it just stopped, but you have not installed any new software or hardware recently,

Hardware Setup 2-1 Chapter 2. Hardware Setup Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or di