Introduction Hardware Setup BIOS Setup Driver & Utility CD Appendix iL-90MV Motherboard Intel Socket 478 (Core Duo) User’s Manual Inte
To install this motherboard: 1. Locate all the screw holes onthe motherboard and the chassis base. 2. Place all the studs or spacersneeded on the c
Hardware Setup iL-90MV 2-3 2.3.1 CMOS Memory Clearing Header and Backup Battery The time to clear the CMOS memory occurs when (a) the CMOS data beco
CMOS Backup Battery: An onboard battery saves the CMOS memory to keep the BIOS information stays on even after disconnected your system with power so
Hardware Setup iL-90MV 2-5 2.3.2 Wake-up Headers These headers use a jumper cap to enable/disable the wake-up function. • USB-PWR1: Pin 1-2 shorted
2.4 Connecting Chassis Components 2.4.1 ATX Power Connectors These connectors provide the connection from an ATX power supply. As the plugs from the
Hardware Setup iL-90MV 2-7 2.4.2 Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the
2.4.3 FAN Power Connectors These connectors each provide power to the cooling fans installed in your system. • CPUFAN1: CPU Fan Power Connector •
Hardware Setup iL-90MV 2-9 2.5 Installing Hardware ※ DO NOT scratch the motherboard when installing hardware. An accidentally scratch of a tiny sur
4. Peel off the protective film from the retention module. This will expose the adhesive sponge. 5. Face the retention module with the side of adh
Hardware Setup iL-90MV 2-11 7. Carefully place the heatsink onto CPU socket in the direction of blowing its airflow toward rear panel. Use a cross
iL-90MV User’s Manual English, 2nd Edition August, 2006 Copyright and Warranty Notice The information in this document is subject to change wit
2.5.2 DDR2 Memory Slots This motherboard provides two 240-pin DIMM slots for Dual Channel DDR2 667/533 memory modules with memory expansion size up t
Hardware Setup iL-90MV 2-13 2.6 Connecting Peripheral Devices 2.6.1 Floppy and IDE Disk Drive Connectors The FDC1 connector connects up to two
2.6.2 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by a thin SATA cable. For more information on
Hardware Setup iL-90MV 2-15 2.6.3 Additional USB 2.0 Port Headers Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to
2.6.5 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. 2.6.6 Front Panel Audio Con
Hardware Setup iL-90MV 2-17 Driver Configuration for AC’97 audio connection: The audio driver is originally configured to support HD Audio. For AC’9
2.6.7 PCI Express X1 Add-on Slot This slot provides the connection of add-on cards that comply with PCI Express specifications. 2.6.8 PCI Add-on
Hardware Setup iL-90MV 2-19 2.7 Onboard Status Display 2.7.1 Power Source Indicators These indicators work as a reminding device to display the powe
2.8 Connecting Rear I/O Devices The rear I/O part of this motherboard provides the following I/O ports: • VGA1: Connects to monitor input. • Mouse
BIOS Setup iL-90MV 3-1 3. BIOS Setup This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS (Basic Input/Out
Introduction Contents 1. Introduction... 1-1 Hardware Setup BIOS Setup Driver &
3.1 Standard CMOS Features Phoenix – AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Tue. Aug 1 2006 Item Help Time
BIOS Setup iL-90MV 3-3 IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave, IDE Channel 3 Master/Slave, IDE Channel 4 Master/Slave Click <En
Cylinder This item configures the numbers of cylinders. Head This item configures the numbers of read/write heads. Precomp This item displays the num
BIOS Setup iL-90MV 3-5 Total Memory This item displays the total memory available in the system.
3.2 Advanced BIOS Features Phoenix – AwardBIOS CMOS Setup Utility Advanced BIOS Features Quick Power on Self Test Enabled Item Help ► CPU
BIOS Setup iL-90MV 3-7 C1E Function This item appears only for certain processors with the C1E (Enhanced Halt State) Function. When set to [Enabled]
※ Don’t forget your password. If you forget the password, you will have to open the computer case and clear all information in the CMOS before you c
BIOS Setup iL-90MV 3-9 3.3 Advanced Chipset Features Phoenix – AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable
PCI Express Root Port Func Click <Enter> key to enter its submenu: Phoenix – AwardBIOS CMOS Setup Utility PCI Express Root Port Func PC
BIOS Setup iL-90MV 3-11 An unmatched configuration will cause the display device abnormal. For example, an HDMI digital device connected to “HDMI Po
3.6 PnP/PCI Configurations ...3-20 3.7 PC Health Status...
3.4 Integrated Peripherals Phoenix – AwardBIOS CMOS Setup Utility Integrated Peripherals ► On-Chip IDE Device Press Enter Item Help ► On-
BIOS Setup iL-90MV 3-13 IDE Bus Master This option enables or disables the IDE bus mastering capability under the DOS environment. On-Chip IDE-1 Con
※ The option [Enhanced Mode] does not support the Windows 98/ME operating system. - PATA IDE Mode This item determines the function mode for “IDE1”
BIOS Setup iL-90MV 3-15 - USB 2.0 Controller This option enables or disables the USB 2.0 controller. - USB Keyboard Support via Select [BIOS] (the
Onboard PCI Device Click <Enter> key to enter its submenu: Phoenix – AwardBIOS CMOS Setup Utility Onboard PCI Device IEEE 1394 Controll
BIOS Setup iL-90MV 3-17 3.5 Power Management Setup Phoenix – AwardBIOS CMOS Setup Utility Power Management Setup ACPI Suspend Type S3(Suspend
Wake Up by Wake# of PCIe When set to [Enabled], access through the add-on PCI Express card can remotely wake up the system that was in Soft-Off condi
BIOS Setup iL-90MV 3-19 ※ The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or USB type. Some PS/2 mice cannot
3.6 PnP/PCI Configurations Phoenix – AwardBIOS CMOS Setup Utility PnP/PCI Configurations Resources Controlled By Auto Item Help X - IRQ
BIOS Setup iL-90MV 3-21 - IRQ Resources Click <Enter> key to enter its submenu: This item sets each system interrupt to either [PCI Device] or
Introduction 1. Introduction 1.1 Features & Specifications CPU • Designed for Intel® Core Duo/Solo, Core 2 Duo socket 478 processors with 667/53
3.7 PC Health Status Phoenix – AwardBIOS CMOS Setup Utility PC Health Status ► ABIT FanEQ Control Press Enter Item Help FAN Fail Alarm Se
BIOS Setup iL-90MV 3-23 CPU FanEQ Control This item allows you to control the CPUFAN speed. When set to [Enabled], the following items become select
Back to PC Health Status Setup Menu FAN Fail Alarm Selectable This item selects the fan that will be monitored for malfunction. Shutdown When FAN F
Driver & Utility CD iL-90MV 4-1 4. Driver & Utility CD The “Driver & Utility CD” that came packed with this motherboard contains drivers
4.1 Intel Chipset Software Installation Utility This utility installs Windows [INF] files to the target system. These files outline to the operating
Driver & Utility CD iL-90MV 4-3 4.2 Intel Matrix Storage Technology Driver This driver provides functionality for the on-chip SATA Controller. ※
4.3 Intel Graphics Media Accelerator Driver This driver provides functionality for the on-chip Graphics Controller. To install this driver: 1. Click
Driver & Utility CD iL-90MV 4-5 4.3.1 Tips on HDMI application 1. Connects to your HDMI device from the connector “HDMI1” only with an HDMI-to
(2) If it does, uncheck the item “Hide modes that this monitor cannot display” in the “Monitor settings” via the path: [Control Panel] [Display Pro
Driver & Utility CD iL-90MV 4-7 6. Also, please remember that you will have to re-configure the “Display Device” every time after disconnecting
• 1x FP-Audio header • 1x CD-IN connector Rear Panel I/O • 1x VGA connector • 1x PS/2 Keyboard connector • 1x PS/2 Mouse connector • 1x HDMI 1
4.4 Realtek Audio Driver This driver provides functionality for the onboard High Definition Audio Codec. To install this driver: 1. Click on the [Dr
Driver & Utility CD iL-90MV 4-9 4.5 Intel PRO Network Connections Driver This driver provides functionality for the onboard Intel Gigabit Networ
4.7 Intel SATA Driver Disk Maker This procedure is necessary if you want to install operating system to a RAID configuration connected among “SATA1~S
Driver & Utility CD iL-90MV 4-11 4.8 ABIT EQ (The Hardware Doctor Utility) ABIT EQ is a self-diagnostic system for PC based on motherboards desi
5. Execute the ABIT EQ by entering the Windows Menu [Start] [All Programs] [ABIT] [ABIT EQ]. 6. ABIT EQ shows you the status of Voltage,
Driver & Utility CD iL-90MV 4-13 4.9 FlashMenu (BIOS Update Utility) ABIT FlashMenu is the most stable Windows-based BIOS flash available. No mo
4-14 iL-90MV
Appendix iL-90MV 5-1 5. Appendix 5.1 Troubleshooting (How to Get Technical Support?) 5.1.1 Q & A Q: Do I need to clear the CMOS before I use a
Step 3. The same procedure as Step 2, but while discharging the CMOS data, pull out the ATX power connectors from motherboard and remove the button b
Appendix iL-90MV 5-3 • CPU: Type in the brand name and the speed (MHz) of your CPU. (Illustrate the over-clocking status if you had done so.) Examp
Introduction 1.2 Motherboard Layout iL-90MV 1-3
5.1.2 Technical Support Form 5-4 iL-90MV Region: E-mail: First name: Last Name: Subject: Motherboard: BIOS Version: CPU: Memory brand: Memo
Appendix iL-90MV 5-5 5.1.3 Universal ABIT Contact Information Taiwan Head Office Universal ABIT Co., Ltd. No. 323, Yang Guang St., Neihu, Taipei, 11
P/N: 4310-0000-37 Rev. 2.00 http://www.abit.com.tw
1-4 iL-90MV
Hardware Setup iL-90MV 2-1 2. Hardware Setup In this chapter we will elaborate all the information you need upon installing this motherboard to your
Kommentare zu diesen Handbüchern